Flysmart Digi

iFlight Taurus X8 Pro 8S HD Cinelifter

Receiver Option

Kuantitas

Ringkasan

+ PRODUCT DESCRIPTION Engineered with professionals for professionals, a BNF that's aimed for carrying big payloads offering a soft-damped universal platform for DSLR or cinema cameras (Red Komodo, Zcam, BMPCC, etc) featuring DJI's FPV HD transmission system. 8-single X-Class grade ESCs for maximum reliability and power. Redundancy is a big safety factor when carrying expensive cinema gear. Even in case of an overload or failure, the remaining ESCs and motors will be able to carry your gear back to you. In case you get troubles with signal interference or radio signal loss the GPS rescue feature will automatically take over control, climb to max flight altitude, fly back in a straight line, and descend towards your liftoff location until the signal transmission is regained (no automated landing). The integrated TPU landing gear provides sufficient height for most terrain and offers some protection on harder landings. 2kg maximum payload for a variety of top-mounted cameras and the ability to fine-adjust the stable mount for a perfectly balanced CG (Center of Gravity). The top mount 8S battery acts as a power source as well as a counterweight for most common cinema camera weights which can be easily exchanged with our iFlight battery quick-release mounting system. The adjustable CNC aluminum camera mount offers angles from 5 to 35 degrees and can be safely secured for reproducible outcomes. No jello, no jitter, no problem; Our silicon-ball dampened carbon camera base is decoupled from the rest of the frame to reduce the amount of vibration generated by motors and propellers. For the perfect cinematic shot, we recommend additional software stabilization in the post (Reelsteady, Gyroflow, etc.) or a hardware module (for example SteadXP). Test data: Flight time with 5.000mAh 8S: - No camera installed: 12min - Installed camera: 6-8min Maximum speed: - Low payload: 160km/h - High payload: 130km/h Payload: - Maximum payload: 2kg - Recommended payload: 1-1.5kg Features: Big size XING2 3110 // The power motors with extreme lift and flight performance 8S power system // More power and speed 8x single X-Class grade ESC motor drivers for more reliability Redundant iFlight ESC Commander PCB // Power distribution board with high capacitance, filtering and heat dissipation GPS module pre-installed (BF GPS rescue or INAV GPS RTH feature available) Universal camera mount and accessories for a wide range of cameras to install Taurus X8 Pro BNF Specs: GPS module: iFlight M8Q-5883-GPS & Compass V2.0 (LINK) Total Dimensions: 430mm*350mm (body dimension) Upper(middle) plate thickness: 3.5mm Weight: 2.3kg±5g (without battery) Bottom plate thickness: 3.5mm BLITZ F7 Pro Flight Controller Motor: XING2 3110 900KV Top plate thickness: 3mm Arm Thickness: 8mm Propeller size: 8 inch Wheelbase: 450mm FC // BLITZ F7 Pro Flight Controller Mount pattern: 35*35mm / 4mm PCB hole diameter Smart audio / IRC Tramp VTX protocol supported Firmware target: IFLIGHT_BLITZ_F7_PRO BlackBox: 512MB Onboard Dimensions: 41*41.5mm BEC: 5V/2.5A, 12V/2A Barometer: DPS310 OSD Chip: AT7456E LED controller: Yes MCU: STM32 F722 Weight: 17g (±2) Beeper pad: Yes Gyro: MPU6000 UARTS: 6 ESC // 2 x iFlight ESC Commander PCB (8x SucceX X80A) Supports up to Dshot600, Proshot, Oneshot, Multishot Firmware Target: iFlight-BL32-PRO Up to 48kHz PWM frequency Mounting pattern: 40*17mm Constant: 80A / Burst: 100A Capacitance: 470uF/35V BlHeli32 telemetry: Yes Current Sensor: Yes Input: 2-8S LIPO Weight:8.1g MCU: F051 BEC: No Taurus X8 Pro HD BNF Included Components and Parts 8 x HQ 8X4X3 CW propeller + 8 x HQ 8X4X3 CW propeller (Color may vary) 2 x Albatross LHCP 5.8GHz SMA FPV Antenna 1 x XT90 Male to XT60 Female Adapter Wire 2 x iFlight Lipo Strap 20*400mm (Black) 2 x iFlight Lipo Strap 20*500mm (Black) 1 x Pre-built and Tested Taurus X8 Pro 1 x DJI FPV Air Unit Module + Camera 1 x CNC Aluminum alloy cam mount 1 x XT90 Smart Smoke Stopper 1 x Prop Wrench

Anda mungkin juga suka