Flysmart Digi

iFlight Taurus X8 HD Cinelifter (DJI Air Unit)

Receiver Option

數量

簡介

+ NOTE: This is a non-stocked item, a lead time of one week may apply. HK LOCAL ORDER ONLY 只限香港本地購買 Engineered with professionals for professionals, a BNF that's aimed for carrying big payloads offering a soft-damped universal platform for DSLR or cinema cameras (Red Komodo, Zcam, BMPCC, etc) featuring DJI's FPV HD transmission system. Redundant ESC and motor setup for maximum performance but also a safety factor. Even in case of an overload or failure, one remaining ESC and 4 motors will be able to carry your expensive camera back to you. In case you get troubles with signal interference, radio signal loss, or complete FPV transmission fail the GPS rescue feature will automatically take over control, climb to max flight altitude, and descent towards your liftoff location until the signal transmission is regained (no automated landing). The integrated TPU landing gear provides sufficient height for most terrain and offers some protection on harder landings. 2kg maximum payload for a variety of top-mounted cameras and the ability to fine-adjust the stable mount for a perfectly balanced CG (Center of Gravity). The underslung battery acts as a power source as well as a counterweight to strategically slide the weight more front or back to counter camera lenses of different weight or length. The adjustable CNC aluminum mount offers angles from 5 to 35 degrees and can be safely secured for reproducible outcomes. No jello, no jitter, no problem; Our silicon-ball dampened carbon camera base is decoupled from the rest of the frame to reduce the amount of vibration generated by motors and propellers. For the perfect cinematic shot we recommend and additional software stabilization in the post or a hardware module (for example SteadXP). The estimated flight time with 6S 4500mAh and attached cinema camera is about 4-6min, depending on speed and wind conditions! Features: XING 2806.5 efficient and powerful wide stator motors Redundant ESC and motor configuration Stable silicon-ball decoupled camera CNC mount GPS flight data and rescue functionality 2kg max payload for various cinema and DSLR cameras Optimized CG through the adjustable camera and battery mount A basic PID- and Filter tuning was applied for a great flight experience! Taurus X8 BNF Specs: SucceX-D F7 TwinG V2.2 Flight Controller Motor: XING 2806.5 1300KV GPS module: iFlight M8Q-5883-GPS & Compass V2.0 Wheelbase: 400mm Body Size: 283*283mmmm Top and bottom plate spacing: 20-31mm (aluminum standoff height) Propeller size: 8 inch Weight: 1574.4g (without battery) FC // SucceX-D F7 TwinG V2.1 MCU: 216MHz STM32F722 Gyro：2x ICM20689 Barometer: YES Blackbox：32MB Betaflight OSD: YES BEC: 5V 2.5A / 9V 2.5A UARTs: 5 Input voltage: Recommended 2-6S, MAX 8S Firmware Target: IFLIGHT_F722_TWING Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm Dimensions: 36*36mm Weight: 7.5g USB type-C ESC // 2x SucceX 80A 2-8S 4in1 MCU: STM32F051 Up to 48kHz PWM frequency Capacitance: 470uF/50V Current Sensor: Yes Input: 2-8S LIPO Constant: 80A / Burst: 100A BlHeli32 telemetry: Yes BEC: No Supports up to Dshot600, Proshot, Oneshot, Multishot Firmware Target: iFlight-BL32-4IN1 Weight:18.6g Mounting pattern: 30.5*30.5mm/Φ3mm Taurus X8 HD BNF Included Components and Parts pre-built and tested Taurus X8 1 x Taurus X8 Frame 1 x DJI FPV Air Unit Module + Camera 4 x Albatross LHCP 5.8GHz SMA FPV Antenna 8 x HQ 8X4X3 CW propeller + 8 x HQ 8X4X3 CW propeller (Color may vary) 2 x iFlight Lipo Strap 20*300mm (Black) 1 x Prop Wrench *Barometer can only be used with Betaflight 4.3.0 and above!

你可能感興趣的商品